o'ring chain oil ?

claw

New member
o.kI know there is o'ring chain lube for your chain. But i like to recycle my motor oil . floored tells me "over a couple of rums"that this will wear my chain out quicker.I have had many different bikes with o'ring chains on them over the years with no problems.I think any lube on them is better than nothing .?
 
S

SmokinJoe

Guest
imported post

imported post

id still buy a nice chain wax o ring friendly spray on, i hate fling off. i like my bike clean when im stickin to the streets and commuting on it. I'd guessmotor oilwould wear your chain over a long period of time
 

3stroke

New member
imported post

imported post

I've used 90wt. gear oil with good results and it is the recomended lube in a lot of shop manuels.It can be a bit messy and is best applyed to a warm chain,like after the ride.
 

Floored

Active member
imported post

imported post

What about used KTM 450EXC engine oil from it's first oil change (full of metal bits), that is poured liberally over your chain (and hence tire and swingarm)?
 

claw

New member
imported post

imported post

worked good on your horn and starter he he . if my chain every breaks i'll usethe old oneto tow you out.
 

edzzed

Member
imported post

imported post

i use castrol chain lube on my klr. been doing that for 32,000 kms and it is not stretched too bad but will be replacing it next week. you will find the best time to lube a chain is after a 20 mile ride. the chain is warm, maybe even hot. that's the primo time to lube it. reason being is the lube will be pulled into the o ring. cold lube will literally suck into the hot chain much like water getting sucked into the bearings of a boat trailer if you don't allow the wheels to cool before putting the trailer into the water. Ed
 

claw

New member
imported post

imported post

do you think oil will destroy the rubber in a o'ring chain ?i never thought to oil a chain after you ride for a bit.
 

edzzed

Member
imported post

imported post

i would assume the o rings will be ok. not 100% so don't quote me. my bike was brand new and still has the original chain. been oiling it that way forever. and gonna keep doing it. Ed
 

Island Hopper

New member
imported post

imported post

I would tend to agree with 3 stroke on using gear oil..... I've gone through 5 sets of chain and sprockets on my 640 with the first four lubed with spray on..... The fifth and my current set I've used 80/90 oil exclusively and have had over a 50% longer service life out of the chainwheels using the gear oil...
 

Floored

Active member
imported post

imported post

Here are a few things I've found on the subject (JSYK, #3 is page 5 of a thread that starts with #4. The reason I've included it on it's own, is that someone has included a bunch of manufacturers recommendations.I found these interesting and don't want this info missed, in case people don't read the whole thread):

#1 - http://www.motorcyclistonline.com/howto/122_0506_motorcycle_chain_lube/index.html

#2 - http://www.webbikeworld.com/r3/motorcycle-chain-cleaner/

#3 - http://www.advrider.com/forums/showthread.php?t=345397&page=5

#4 - http://www.advrider.com/forums/showthread.php?t=345397
 

sagot

Member
imported post

imported post

I use X-ring chains and I don't lube them at all.

An X-ring or O-ring chain is like a sealed bering. As the roller comes into contact with the chain wheel it stops and the internal lube takes over. The internal lube canot come out nor can you "spray" anything in.

I use to lube my chains and got maby another 1000 KM out of them but man what a pain.

Anyway how long does that oil stay on in wet/muddy condtions? 1000-1500 ft.

My opinion.
 

edzzed

Member
imported post

imported post

now if only they could come up with x rings for my boat trailer. mind you they do have oil bath bearings. Ed


sagot wrote:
I use X-ring chains and I don't lube them at all.

An X-ring or O-ring chain is like a sealed bering. As the roller comes into contact with the chain wheel it stops and the internal lube takes over. The internal lube canot come out nor can you "spray" anything in.

I use to lube my chains and got maby another 1000 KM out of them but man what a pain.

Anyway how long does that oil stay on in wet/muddy condtions? 1000-1500 ft.

My opinion.
 

Sparkle

New member
imported post

imported post

It's true that a 'O' ring chain will run unlubricated and dirty for a long time, but whenit comes to a dirty chain, it isn't so much the chain rollers that take the damage. A muddy chain, loaded full of abrasives will hook your sprockets in short order as well as sometimes stretch the chain because of reduced chain slack caused by periodic lumps.

Cleaning and lubricating your 'o' ring chain will not only make your chain last longer, but it will reduce the friction power loss, and improve the life of your expensive sprockets. I use WD40 to loosen the grit, and then spin the chain with the back wheel while wiping with a rag until the chain is clean and the lubricant is almost gone. And I give the rear sprocket a wipe too.

It's important that the rollers can seat fully into the sprocket wells so the chain-roller doesn'tslam back and forth between the sprocket teeth on a bed of grit.

I've seen quad guys with exposed chain drivecarry a small bristle brush for the real muddy stuff, and it might not be a bad idea.

Just my opinion....

Sparkle
 

claw

New member
imported post

imported post

I would have to agree clean and lube should get a lot more time out of a chain. I have learned a couple of things with this post thanks for all the input.I oil my chain after it is clean and dry if you oil the day before there is little oil flying off your chain.wd-40 to clean after your wash good idea oil chain after you ride when your chain is warm good idea.So leaving your bike dirty and not washing the grit off the chain will do more damage then cleaning and oiling. thanks
 

sparklr

New member
imported post

imported post

Seems there are many differing opinions on the O-ring chain matter when it comes to lubing and cleaning. Many of us maintain the tried and tested methods we are all familiar with. When protecting my minimal investment, I chose to slather away with racing lube. What a mess, for both application and removal. I have come to an assessment that any lube that stays wet just attracts the miscreants that do the most harm. Not to mention that if it is wet, it is also more likely to be water soluble.

Heat, the real chain killer. With dirt and grime comes friction, friction causes heat. Eliminating dirt from the equation helps reduce the heat. Improper chain tension and rider behaviour also contribute to the heat factor. Any liquid will heat up with friction, thin out and draw out of its intended point of protection, thanks to capilliary action the miscreants enjoy the ride also.

Hence, I decided to use the Teflon spray all over the chain and sprockets. No mess, dries clear and never needs a bath. You have to overcome the fear of seeing your chain with an unlubricated appearance. Cleaning a chain, unheard of!!

:)

Happy lubing.
 
O

oldguy

Guest
imported post

imported post

Yes. You can spend a fortune on fancy chain wax and lubes. I have several flavours sitting on a shelf for some years now.

They were replaced with plain old WD-40.

Logged many miles with sportbikes using wd-40. Carried a little can of it with me. Spray the chain down every night on long trips. WD was the only thing I found that would resist rust in wet conditions and it did not turn into grinding compound, like most lubes, when mixed with grit.

Three off road bikes on dirt, rock, gravel roads 90 percent of the time. Same thing - spray the chains down after every trip. Use a brush on the chains and sprockets occasionally. No rusty chains and very little stretch(meaning very little wear).

WD-40 has saved me a fortune in chain.
 

2Trider

New member
imported post

imported post

WD40 is my "chain lube" only to keep the rust from forming on the chain

O-ring chains already come lubed internally so that's good enough for me.

My chains wear outfrom stretch and the bigger the HP with a happy throttle handthe faster it stretches.

whether the stretch is from the side plates growing or more from the pins wearing internally...no additional lube is going to help IMO.

:hb:
 
O

old trials guy

Guest
imported post

imported post

Since everyone is giving inputs I will throw in my comments. Most manufacturers recommend gear oil for lubing an o-ring chain. I think the intention is to keep the o-rings healthy which in turn keeps crap out of the rollers and the factory lube inside. I clean chains (both o-ring and standard type) regularly and use lots of WD after washing to displace water and prevent rust. I use some lube to reduce friction between chain and sprocket like Sparkle recommends. If your bike has a crankcase breather without a catch bottle, try routing it over the chain so any oil pushed out will end up on your chain.

One trick I learned over the years is not to over tighten your chain. Especially O-ring chains. Once a new O-ring chain initially stretches and settles in they tend to find a "sweet spot" which is generally near the recommended upper limit of slack in the chain. If you leave it alone I find it will stay at that point for many miles. If you constantly adjust to the lower limit of slack they tend to stretch back to that sweet spot. Constant adjustment seems to add up to premature stretching.

I also have noticed through the years many folks don't really understand how much free play should be in the chain on a long suspension travel bike. Long travel means the chain needs lots of slack otherwise you are loading the chain, sprockets and transmission when the suspension is at full travel. Make sure you read your manual and myopnion is it is better to be a little sloppy than too tight.

otg
 

Loz

New member
imported post

imported post

After I clean the bike with water and detergent, including the chain, I let it dry for a few days then scrub it with a wire brush to remove as much dirt as possible. I do get spots of rust forming but is exterior and superficial.
After scrubbing I lube liberally with chain saw chain oil. Spin the wheel plenty as it goes on from the tip of an oil can. Then leave it for a few days untill next weekend.

I find that the chain is pretty dry and muddy after a ride but the o-rings stay nicely lubed and pretty clean.
 

Buck

Moderator
imported post

imported post

I use kerosene to clean, costs less than wd-40 and that's what the chain manufacturer and owners manual recommends for o-ring chains.

Lube with summer weight (heavy)chainsaw bar oil, let it soak in overnight.

Chains/sprockets need lube with an EP (extreme pressure) additive. Gearlube and chainsaw oil has this.
 
Top