Ballancing wheels...

G

Guest

Guest
Just wondering if anyone knows where I can get this down cheaply and quickly. Thanks.
 

04klr

Well-known member
imported post

imported post

it may not be good nuff for the moto gp guys but, two eye scews in the garage ceiling approx 10" apart, make a loop of string around (get it loop, around, never mind) 6', thread the loop thru the eyes with approx. 3' hanging down on each sidethen just hang your wheel (axle installed) with one end of the loop over each side, the loop (being a loop) will be self levelling, then "giver" a little spin and wait, add lead, spin wait, done, or at least good nuff done, a 200k sportbike may want to pay the bucks for a shop, but for my KLR/KLX this method is way easyand more than accurate enuf, did I mention it's free. (except for the screws string and BEER)
 

joker650

Active member
imported post

imported post



Thanks Wayne :clap:



..............but why didn't u tell us that on the tire weekend ? :mad3:
 
O

old trials guy

Guest
imported post

imported post

I usually just buy some good stick on wheel weights and spin the wheels on the bike. Typically the heavy spot will be the where the rim lock is. I place two sets of weights at 120 degrees from the rim lock so you end up with three heavy points on the wheel further reducing vibration.

It is not deadly accurate but with some patience it works fine. Make sure the wheel is clear of the ground (duh) and the brake isn't dragging. Rear wheel you will have to remove the chain.

Make sure you clean the rim well before applying the weights. I use some brake clean or alcohol to remove any grease or oil. If you are too cheap to buy weights try wrapping lead tin solder around the base of the spokes.

:tup:eek:tg
 
G

Guest

Guest
imported post

imported post

Turns out they probably didn't counter balance the wheels, but I really can't feel any more vibration than I used to, for the newbie ride I think they'll do fine. I'll balance them after the newbie ride for sure.

Anyone know where I can get those strip weights? My local bike shop doesn't wholesale them, neither does my local tire place.
 
O

old trials guy

Guest
imported post

imported post

Lordco,Napaor anywhere they sell mag wheels.

otg
 
G

Guest

Guest
imported post

imported post

Ok, I went over to Lordco and bought myself, 6 1 foot strips of 1/4 oz weights.

I have rim locks on both the front and back tire. about how many should I put on to balance them? do I need to build a rig? Take the wheels off the bike?
 
O

old trials guy

Guest
imported post

imported post

Tibarus wrote:
Ok, I went over to Lordco and bought myself, 6 1 foot strips of 1/4 oz weights.

I have rim locks on both the front and back tire. about how many should I put on to balance them? do I need to build a rig? Take the wheels off the bike?

Read my post above. Simple and it works. Just use some masking tape to experiment, when you have enough weight so the wheel stops in random positions you are there. I formed the weights to fit theshape of the rim between the spokesso they are centered and out of the way.

otg
 
G

Guest

Guest
imported post

imported post

old trials guy wrote:
Tibarus wrote:
Ok, I went over to Lordco and bought myself, 6 1 foot strips of 1/4 oz weights.

I have rim locks on both the front and back tire. about how many should I put on to balance them? do I need to build a rig? Take the wheels off the bike?

Read my post above. Simple and it works. Just use some masking tape to experiment, when you have enough weight so the wheel stops in random positions you are there. I formed the weights to fit theshape of the rim between the spokesso they are centered and out of the way.

otg

How did you "form" them?
 

tomcycle

Past President DSBC 2004 -2018
Staff member
imported post

imported post

You will need to make a set up like this, its not perfect but it will work with your situation

balance2.jpg


It must be level

Get a round peice of machined rod, about 3/8" diameter, make sure it is not bent. The rod should be about 1/2 of the diameter of your axle.

Heavy side of the wheel will always go to the bottom

apply weights to the opposite side

You will need lots probably 6-8 ozs

If you have done everything right you will be able to put the wheel in any position and it wont move, if you roll the wheel gently it should stop in a different psotion each time.

Good luck
 

farmerger

Member
imported post

imported post

I put the Dynabeads in my new TKCs last year. No vibes, and no balancing required.:hb::clap::tup:
 

Sparkle

New member
imported post

imported post

I've had the same wheel weights on my old bike for years and with tire changes I never seem to notice a differance. A'course I'm not all that speedy either. When I did balance my wheels after I tire change here's how I did it:

1. Hammer a 6 inch nail into a roof beam of your shed or garage.

2. Insert the axle into the wheel and thread a strongcord or wire through the cotter- hole of the axle. I used heavy copper wire and tried to get theknot to be centered over the axle diameter so the wire wasaligned with the axle.

3. Make a loop on the cord so you can hang the wheel horizontal in the air hanging from the nail.

If the tire is perfectly balanced it will hang relatively level. If one side sags place weights on the opposite side until it's level. Move the weights around until you find balance with the minimum weight. I usedfishing sinkers cut in halfand just squeezed over the spokes.

(edit) (the closer to the wheel the string is, the more sensitive the balance and you may have to add a spacer to the bottom of the axle. Also a "pointer stick" just touching the tire surface might help indicate the high and low spots.)

It might be worth a try if you have the wheel off anyway...

Sparkle
 

Attachments

  • wheelbal.JPG
    wheelbal.JPG
    10.5 KB · Views: 0
G

Guest

Guest
imported post

imported post

I ended up doing the wheel balancing OTG's way, removing the brake and chain and letting it free wheel. Worked great and the bit doesn't rattle anymore.

Thanks for all input ^^
 
Top