dynojet kit install. Do it yourself or have shop do it for you

F

formosahenry

Guest
I am interested in installing the Dynojet kit on my 04 DRZ400S. I was told by a shop that if I make a mistake, it will cost me a new carburator. Did anyone out there install the kit themselves or did you just take it to the shop and have them installed it for you? Is it easy for a do-it-yourselfer? How can you screw up the carb? How long does it take? How much tuning do you have to do? Any success stories and horror story out there? Thanks to all that reply.
 

DRuZer

Member
imported post

imported post

I like my DJ kit. I installed it myself and it wasn't particularly difficult.
You need to drill out a thin aluminum plug to access the low speed fuel screw, but other than that, its just removing the carb, removing the float bowl and the slide. (Oh yeah, and reassembly)

If this sounds beyond your comfort level, by all means, let a dealer do it. But remember the words of a man who knows better:
"If I wanted the job screwed up, I would have done it myself!"
Make sure you are dealing with a good mechanic.

I'm not sure which jets will work best for you, but I can reccommend the settings for the bike if you enlarge hole in the top of the airbox.
Guy
 

dan627

New member
imported post

imported post

i am going to be installing the dj stage 1 kit soon in my klx, i asked the question to burned on tt and he said with the dj stage 1 kit installed just remove the snorkel,do not cut out the 3x3 ! i have been reading up on it latley and i think i will attempt the job myself, looks like the hardest part is getting the carb out then back in again ! i am also going to install the extended fuel screw at the same time ..hope this helps some !...
 
J

jburnin

Guest
imported post

imported post

to take the carb out easier undo the upper rear subframe bolt and drop the subframe. it only gives you about 3/4" more room but believe me every little bit helps, also if your worried about your frame tape it up because the carb will scratch it when you pull it out. GOOD LUCK
 

DRuZer

Member
imported post

imported post

Hmm, I wonder why burned on TT has finally changed his tune (or should I say tuning)?

For years(!) he's been telling everyone to cut the airbox. I wonder how long he ran his 400S with the jet kit before he swapped it for the offroad carb, race cams, etc. He does sound confident about his reccommendations.

Did he mention where you should set the needle and which main jet to use? I can always RTV the peice back onto the top of the airbox and test it out....
 
J

jburnin

Guest
imported post

imported post

I don't think he changed his tune its just that if you don't mod the airbox you can use the jets provided in the dj kit, but if you do mod the airbox you have to get different jets. Call Jesse at kientech he is the man he'll hook you up with everything you need, and he'll answer all your questions .http://www.kientech.com/:tup:
 

dan627

New member
imported post

imported post

when i asked burned i told him my bike was completly stock and i wanted to keep it that way for reliability,that is why he suggested the dj stage 1, and just removing the snorkel! if you did the 3x3 then you would have to change needle ,jet ect...the dj kit is supposed to give you better responce and a crisper take off.
 
J

jburnin

Guest
imported post

imported post

sounds like you've done your homework, you'll love the difference the dj kit will give you, YEEEHAAA!!!!. If you do want more though, give jesse a call he helped me out a lot!!!:D
 
S

Starbucks

Guest
imported post

imported post

The DJ kit is, humbly, pure s***. Your bike will run worse and eat more gas (IMHO), with some gains in roll onin the mid range. The bottom and top I found were worse.

I know cus I had the shop install it...as per DJ specs.

Then I did the full burned / kinetech mod. It spins like a top, better all round, less gas consumption, better in every way.

Doing it yourself is a peice of cake, on the 400 it takes about 1 hour from start to finish if you have the right tools. It's just one single carb that basically pops in and out like lego--pretty simple.

Do the full meal deal,I think few are happy with the DJ kit--I even preferred stock to the DJ kit. You may want to run a drill thorugh the exhaust baffles as well, just 5 mm, enough to let some gas through but not enough to louden it up much. Also, drill out the end cap with a bimetal hole saw, but don't cut the arrestor out.

Mine fires right up with nochoke and runs real good!

There's alot of mythology about the snorkel. Some say it's a restrictor, others say its to prevent water and debris entry. There's some merit to these ideas--but really it is a well-enigineered part of the intake system, not an afterthought.

The type ofair flow required by the stockjetting and a cv carb requires air moleculesthat arrivewithin a certain range of velocities. For the stock layout, the snorkel serves as an air accellerator--like the venturi effect in a carb. The air that sits in the box is enough to service the pilot jet and needle jet duing an easy roll on up to where the snorkel and main jet comes into play. So you need more immediate air in the air box, hence, the DJ reccomendation of removing the snorkel. It isn't any great improvement--you won't notice, but it probably made some hairs-breadth difference on a few dyno runs as they were developing the kit, so they say to go with snorkel out. Snorkel out lets in more immediate air for the pilot and the first 1-4 of needle jet roll on. Snorkel in lets in more constant air from 1-4 to full throttle.

The DJ kit unmodified just dumps in a lot more gas on the pilot. The DJ kit tries to compensate for the fact that this is a CV carb by just dumping more gas and air on the pilt, and hoping for the best. But a CV carb is a CV carb...if you want throttle wheelies, you needto paradigm shift and change your jetting look out: Jet it like it is a sport bike carb not an off-road carb. You'll never get the instant throttle snap out of it you would on a pumper carb--but that's ok, it's a dual sport bike.

Just go for a good clean tuning that is smooth and revvy from top to bottom without surging--like a sport bike. If you live in southwestern BC and don't go about 5000 feet much, burned's reccomendations are basically perfect. If you go above 5000 a lot, you'll get a little blubbery-rich, but it still runs pretty good. If it gets too rich on roll-ons, just pull off the carb top and drop the needle down one clip position. If it gets to rich on the main, drop down one jet size. Most assume all bikes are jetted lean and the goal of more power is just to jet them for more gas. This is the rationale of the DJ kit and I think it is wrong. The goal of a good tuning is a decent fuel air ratio throughout the entire rev range under all sorts of engine loads--acelleration and decelleration. In ever dyno'd my DJ kitted 400, but it just felt "wrong" there was too much gas in the wrong places in the wrong times.

Once someone has a good textbook Burned tuning they never want for another. The caveat of course is that you will need to dial in burned's "altitude tuning" or your own custom variation of this tuning if you are in the high country all the time.

So go all the way. Get the jets & hardware from Jesse, and dial it in right yourself. It will cost you less in labor, parts, and gas. Plus it's fun!
 

dan627

New member
imported post

imported post

what is the full burned/kinetech mode ! i agree with the snorkal i would rather leave it on, it was put there for a reason ! i was hoping to get my bike to run a little better at lower speeds, like idling in 1st gear,or in first gear with just a little gas without so much jumping (bucking ).i follow my little guy he is 6 years old and some times he goes pretty slow ! if it was to get better pick up and better gas milage that would be a bonus !
 
S

Starbucks

Guest
imported post

imported post

dan627 wrote:
what is the full burned/kinetech mode ! i agree with the snorkal i would rather leave it on, it was put there for a reason ! i was hoping to get my bike to run a little better at lower speeds, like idling in 1st gear,or in first gear with just a little gas without so much jumping (bucking ).i follow my little guy he is 6 years old and some times he goes pretty slow ! if it was to get better pick up and better gas milage that would be a bonus !
Just call Jesse and tell him what you're doing and he'll hook you up, great service.

http://www.kientech.com/DRZ400ProdList.htm

get:

DynoJet Kit

DRZ400S stainless steel socket head bowl screws

Extended fuel mixture screw.

You will also need to buy these jets seperately and use them with the DJ kit. Do not use the DJ jets.
Main jet:140
Pilot Jet:25
Fuel screw (turns out): 2.5 turns
Needle/Clip position: Dj needle/spring 4th position for clip
Airbox lid: 3x3 (glue screen material over hole to block debris
Pipe: Drill 5mm to 1cm hole through all baffles & remove end cap with bimetal hole saw.

If you need help I'll be glad to...
 

dan627

New member
imported post

imported post

thanks:D , i hope to do this just before the new year or just after! and i will give jessie a call .
 
Top