Noobie Ride Sunday October 18, 2009 DISCUSSION THREAD

ktmken

New member
imported post

imported post

It is a good idea to be self sufficient on the trail even if you are riding with a group.
so.....you should have everything you need to change a tube including air.

- tire irons
-tube ( a 21 inch will work in a 18 tire well enough to get you out of the bush)
-air (small compressor or compressed air)
-tools to get your wheel off of the bike

Or maybe everyone is just carrying their lunch in the backpack ;)

KTMKen
 

Lucky

New member
imported post

imported post

Hi guys, do you have some advice how to tie down 2 bikes to a flat bed trailer?

Should the kickstands be up or down?

:?
 

tomcycle

Past President DSBC 2004 -2018
Staff member
imported post

imported post

Lucky wrote:
Hi guys, do you have some advice how to tie down 2 bikes to a flat bed trailer?

Should the kickstands be up or down?

:?

You will need three thinks

1 a block on the deck of the trailer to keepthe front wheel to keep the bike from rolling forward

2 a block for your front suspension, a 4x4 block about 10 inches long that sits on the front wheel and when the suspension is compressed will have the steering head resting on the top

3 two tie down straps, on the front end of the bike from the handle bars or triple tree clamps, that compress the suspension onto the block you have sitting on the top of you tire, pulling the bik forward into the block or wheel stop on your trailer

If I have time I will post a picture of how I do my bikes.

Tom
 

Lucky

New member
imported post

imported post

tomcycle wrote:
You will need three things
1 a block on the deck of the trailer to keepthe front wheel to keep the bike from rolling forward
2 a block for your front suspension, a 4x4 block about 10 inches long that sits on the front wheel and when the suspension is compressed will have the steering head resting on the top
3 two tie down straps, on the front end of the bike from the handle bars or triple tree clamps, that compress the suspension onto the block you have sitting on the top of you tire, pulling the bik forward into the block or wheel stop on your trailer
If I have time I will post a picture of how I do my bikes.
Tom
[/quote]

thank Tom, a picture would be great, if you can manage it...
 

skidmark43

Administrator / BFF in the blue jacket
imported post

imported post

Six of us went out yesterday to do some trail clearing and post arrows.

Trails and roads are in very good condition. Not much mud / puddles, but it looks like that will change this week.

It was very cold yesterday in the shade and along the main roads at speed... then hot & steamy in the trails.
 

Lucky

New member
imported post

imported post

tomcycle wrote:
Lucky wrote:
Hi guys, do you have some advice how to tie down 2 bikes to a flat bed trailer?

Should the kickstands be up or down?

:?

You will need three thinks

...

If I have time I will post a picture of how I do my bikes.

Tom

Hey Tom,

1. should the bike be in neutral or first?

2. should the front wheel be straight?
 

tomcycle

Past President DSBC 2004 -2018
Staff member
imported post

imported post

Lucky wrote:
tomcycle wrote:
Lucky wrote:
Hi guys, do you have some advice how to tie down 2 bikes to a flat bed trailer?

Should the kickstands be up or down?

:?

You will need three thinks

...

If I have time I will post a picture of how I do my bikes.

Tom

Hey Tom,

1. should the bike be in neutral or first?

2. should the front wheel be straight?

Go to http://www.dualsportbc.com/forums/view_topic.php?id=9169&forum_id=32&jump_to=81756for all the information

but to answer you questions I leave my bike in neutral (for no paticular reason). Not sure what you mean by the front wheel straight, but I do like everything to be at right angles, it just ties down better and its easier to see you have done the job right or if something moves while you are traveling.
 

tomcycle

Past President DSBC 2004 -2018
Staff member
imported post

imported post

We now have all the arrowing up for the Newbie Ride so now its time to show a few photos

For those of you whe are going to challange the Church Mtn Loop this is what you might see

[align=center] [/align]
[align=left][/align]
[align=left]Before we cleared the road of overgrowth[/align]
[align=left] [/align]
[align=left] [/align]
[align=left] [/align]
[align=left]Now After, nice and wide no face slappers[/align]
[align=left] [/align]
[align=left][/align]
 

Fjr eh

Member
imported post

imported post

Won't be able to make this year. We're (Buckethead, Vexorg and I) off to Moab for some slick rock. I'll miss the fun and the ride. Pat and I pre road, most of the route last Sunday. Great ride, don't miss it!
 

klrroo

Member
imported post

imported post

Just a question...... if a guy were to leave Kamloops early the morning of, how early would that guy need to leave by?:DThat harder route looks real nice...
 
J

joshuascottpaul

Guest
imported post

imported post

- tire irons

done

-tube ( a 21 inch will work in a 18 tire well enough to get you out of the bush)

done

-air (small compressor or compressed air)

what do you recommend? where could i get this?

-tools to get your wheel off of the bike

done
 

ktmken

New member
imported post

imported post

You can get a kit similar to this one at most bicycle shops I usually carry 4 or 5 co2 cartridges with me.

http://image.motorcyclistonline.com/f/8648519/123_0444_repair05_z.jpg

or you can pick up a small aircompressor at Canadian Tire like this one.











On my 950 I carry both under the seat and on the DRZ I only carry the co2 system in my tool kit or in my backpack. I have never used these on my own bike, but I have helped out many other people with them.

It is also a good idea to see if it all works by doing a trial run in your driveway using only what you are carrying on your bike.

Have fun

KTMKen
 
J

joshuascottpaul

Guest
imported post

imported post

The C02 tire patch kts are hard to find. I can't find anyone local that stocks these.... Any advice where to pick them up in Vancouver?
 
O

old trials guy

Guest
imported post

imported post

joshuascottpaul wrote:
-air (small compressor or compressed air)

what do you recommend? where could i get this?
I just carry a mountain bike pump. Yes, its slow, but its light, cheap :pand reliable.

otg
 
S

sicamoose1

Guest
imported post

imported post

Kamloops to Chilliwack (Cultas) is about 3 hours maximum, unless you're doing the speed limit the whole way
 
C

cruiser450

Guest
imported post

imported post

I was wondering if it is possible to do the /logging road portion only(or start there),i wanted to do the ride but have a non plated bike.is this possible or no such chance.i know its posted plated only but i have heard some have done previous rides.

john
 

tomcycle

Past President DSBC 2004 -2018
Staff member
imported post

imported post

cruiser450 wrote:
I was wondering if it is possible to do the /logging road portion only(or start there),i wanted to do the ride but have a non plated bike.is this possible or no such chance.i know its posted plated only but i have heard some have done previous rides.

john

John, you will have to drive to the end of Sleepy Hollow road tot he gate, there you can unloadyour bike and ride as far as Tamahi, Lots of trails on Chruch to keep you bussy until everyone comes back. You will miss out on the lunch and test rides.

Tom
 

Phoenix

New member
imported post

imported post

joshuascottpaul wrote:
The C02 tire patch kts are hard to find. I can't find anyone local that stocks these.... Any advice where to pick them up in Vancouver?
Most of the decent shops carry co2 inflators/kits, if you buy one there are various co2 cartridges involved. Most common is the 16 gram non threaded, which when purchased as replacement through any m/c shop will be pricey. It is possible to use 12 gram cartrridges in such units by carrying a 1/2" nut to place under the smaller cartridge providing the necessary seal. The 12 gram cartridges are available in bulk for air pistols/rifles at a much cheaper price at retailers such ad Can. Tire. A viable alternative is a specialty bicycletire pump that also has the abillity to use co2 cartridges as well.Available at bicycle stores.
 

dirtrider

Member
imported post

imported post

Phoenix wrote:
joshuascottpaul wrote:
The C02 tire patch kts are hard to find. I can't find anyone local that stocks these.... Any advice where to pick them up in Vancouver?
Most of the decent shops carry co2 inflators/kits, if you buy one there are various co2 cartridges involved. Most common is the 16 gram non threaded, which when purchased as replacement through any m/c shop will be pricey. It is possible to use 12 gram cartrridges in such units by carrying a 1/2" nut to place under the smaller cartridge providing the necessary seal. The 12 gram cartridges are available in bulk for air pistols/rifles at a much cheaper price at retailers such ad Can. Tire. A viable alternative is a specialty bicycletire pump that also has the abillity to use co2 cartridges as well.Available at bicycle stores.
You can get the CO2 tire fillers at Caps or mountain equipment....however these are one shot fillers....in my experience sometimes you miss fixing the tire right the first time...( thorns, nails, screws ) can and has poked more than one hole...and you should always pump the tube up to check that all holes are fixed before you put it back together....For myself I perfer a mountain bike pump, they cost about $9.00 and weigh less than if you carry a few co2 cartidges and the adapter...you can tape or zip tie them anywhere on the bike...
 
Top