Hi there, I have a '96 DR350 street legal and I"m a newb when it comes to mechanical stuff. I got my bike last October and have not had it on the road yet (had our first snow free day in PG last week
) and I've been slowly farkling up the bike to get it ready.
As such I wanted to do the Jesse air box mod, so I sent my carb to Jesse to have him check it out and install the new needle, fuel screw etc (told ya I was a newb).
Well I didn't think to lable where all the hoses came off from, it looked obvious at the time but that was 3 months ago. I just installed the carb yesterday (almost gave up trying to squeeze it back into the rubber boot at each end!) and I have some extra hoses and holes on the carb still but alas it is not obvious where each goes.
I had a look at the shop mannual that a very kind inmate made available to us but its weak in specifics at this level so given I've seen some great detailed photos/descriptions on this forum about other "stuff" I thought I would look to you folks for assistance.
Also I installed a Acerbis tank and there was no fuel "T" included in the mounting package, can I go to an auto supply store and get something that would work?
Also after the tank instal I had two lock washers and a black disk thing (about 1.5" in diametre, see photo below) with a raised center piece (~1/4" tall) which has the words Acerbis in raised letters on it left over from the package and I have no idea where they go (instructions are a bit cryptic).
Also what is the best spark plug to use? I ordered one from Rocky MTN and it was too large.
Also I'm having trouble getting the rear left turn signal bulb to work. I push the bulb in and sometimes it flashes while I hold it (about 1 out of 10-15 trys) but as soon as I let it go it goes off. I tried different ways of pushing it in but I can't get the contact to stay working. Trying another bulb did nothing. I'm thinking it would be easier to just buy a replacement signal/wire set up given the time I've spent on it so far. I know its a problem where the bulb makes contact inside with the spring loaded portion of the female part because when I hold/push on the wires coming out of the back of the signal casing when I push the bulb in I can get the bulb to light up, but not signal sometimes, but I have not been able to find a way of making it stay on and signaling).
Thanks folks!
As such I wanted to do the Jesse air box mod, so I sent my carb to Jesse to have him check it out and install the new needle, fuel screw etc (told ya I was a newb).
Well I didn't think to lable where all the hoses came off from, it looked obvious at the time but that was 3 months ago. I just installed the carb yesterday (almost gave up trying to squeeze it back into the rubber boot at each end!) and I have some extra hoses and holes on the carb still but alas it is not obvious where each goes.
I had a look at the shop mannual that a very kind inmate made available to us but its weak in specifics at this level so given I've seen some great detailed photos/descriptions on this forum about other "stuff" I thought I would look to you folks for assistance.
Also I installed a Acerbis tank and there was no fuel "T" included in the mounting package, can I go to an auto supply store and get something that would work?
Also after the tank instal I had two lock washers and a black disk thing (about 1.5" in diametre, see photo below) with a raised center piece (~1/4" tall) which has the words Acerbis in raised letters on it left over from the package and I have no idea where they go (instructions are a bit cryptic).
Also what is the best spark plug to use? I ordered one from Rocky MTN and it was too large.
Also I'm having trouble getting the rear left turn signal bulb to work. I push the bulb in and sometimes it flashes while I hold it (about 1 out of 10-15 trys) but as soon as I let it go it goes off. I tried different ways of pushing it in but I can't get the contact to stay working. Trying another bulb did nothing. I'm thinking it would be easier to just buy a replacement signal/wire set up given the time I've spent on it so far. I know its a problem where the bulb makes contact inside with the spring loaded portion of the female part because when I hold/push on the wires coming out of the back of the signal casing when I push the bulb in I can get the bulb to light up, but not signal sometimes, but I have not been able to find a way of making it stay on and signaling).
Thanks folks!
Attachments
Last edited: