'96 DR350 Help, where do all the Carb hoses go....?

scharfg

Member
Hi there, I have a '96 DR350 street legal and I"m a newb when it comes to mechanical stuff. I got my bike last October and have not had it on the road yet (had our first snow free day in PG last week :p ) and I've been slowly farkling up the bike to get it ready.

As such I wanted to do the Jesse air box mod, so I sent my carb to Jesse to have him check it out and install the new needle, fuel screw etc (told ya I was a newb).

Well I didn't think to lable where all the hoses came off from, it looked obvious at the time but that was 3 months ago. I just installed the carb yesterday (almost gave up trying to squeeze it back into the rubber boot at each end!) and I have some extra hoses and holes on the carb still but alas it is not obvious where each goes.

I had a look at the shop mannual that a very kind inmate made available to us but its weak in specifics at this level so given I've seen some great detailed photos/descriptions on this forum about other "stuff" I thought I would look to you folks for assistance.

Also I installed a Acerbis tank and there was no fuel "T" included in the mounting package, can I go to an auto supply store and get something that would work?

Also after the tank instal I had two lock washers and a black disk thing (about 1.5" in diametre, see photo below) with a raised center piece (~1/4" tall) which has the words Acerbis in raised letters on it left over from the package and I have no idea where they go (instructions are a bit cryptic).

Also what is the best spark plug to use? I ordered one from Rocky MTN and it was too large.

Also I'm having trouble getting the rear left turn signal bulb to work. I push the bulb in and sometimes it flashes while I hold it (about 1 out of 10-15 trys) but as soon as I let it go it goes off. I tried different ways of pushing it in but I can't get the contact to stay working. Trying another bulb did nothing. I'm thinking it would be easier to just buy a replacement signal/wire set up given the time I've spent on it so far. I know its a problem where the bulb makes contact inside with the spring loaded portion of the female part because when I hold/push on the wires coming out of the back of the signal casing when I push the bulb in I can get the bulb to light up, but not signal sometimes, but I have not been able to find a way of making it stay on and signaling).

Thanks folks!
 

Attachments

  • Acerbis black thing 2.jpg
    Acerbis black thing 2.jpg
    45.7 KB · Views: 0
Last edited:

Katui

New member
Not sure if you have fixed the carb or not but there should only be a few hoses coming out of it if its mostly similar to the carb on my DRZ 400:
* You will have a bowl exhaust/overflow which should be a fairly thick tube coming out and pointing downwards, it doesn't attach to anything, its just there to keep the bowl at atmospheric pressure.
* You will have your fuel intake which should run in to your carb just above the bowl(bellow where you can see through, there is a little "bowl" that holds fuel before it is used), you have to plug this into your fuel tank via a rubber hose.
* If you have a vacuum actuated petcock(the bit that your turn to switch to reserve) then there should also be a small hose that connects from the top of the cylinder side of the carb to your petcock. This is a small vacuum tube that uses suction from Bernoullis principle inside your carburetor to turn your petcock on and off as needed.

Images of your carb and your petcock would help greatly as its slim picking on google image search. If you have some(or are willing to take some) then PM them or email them to me.
 

scharfg

Member
Hi there Katui, thanks so much for the feedback and assistance. I was able to figure it out with the help of some other folks on the ADrider forum.

Turns out that black Acerbis disk is to keep the dust out of the top of my fuel tank cap.

Take care and thanks again!
 
Top