Broke off plug on a DR 650

windaddiction

New member
First off doh.... I was taknig the plugs out today to look at them and I got one out but the center one sheered off in teh head. What the heck do I do now guys ? How hard is it to remove the head?
 
S

Sixgill

Guest
imported post

imported post

Depending on whats left of the plug i would attempt to center drill it and then use a "broken blot remover" looks like a screw or a square punch with a biteing edge.

As for Head Removal, if you join up with Yahoo DR650 forum you can download the manual for free. Or i can email you specific pages if you like.
 
P

Pirate

Guest
imported post

imported post

I would imagine that it would be possible to use an easy out. I understand that they are not too expensive to purchase and quite often do the trick. Of course they come in various sizes. I would certainly look in this direction before taking the head off...Good luck.
 

windaddiction

New member
imported post

imported post

Ya I'll have to give that a try first. I cranked it over to blow out the rest of the ceramic bits and now there is just a hole so I hope nothing fell in!
 

joker650

Active member
imported post

imported post

windaddiction wrote:
Ya I'll have to give that a try first. I cranked it over to blow out the rest of the ceramic bits and now there is just a hole so I hope nothing fell in!


I hate to be negitive but..............

There may still be peices of cermic in the engine . Small peices prolly got lodged between the piston and the cylinder.

If you have mechanical skills , in about 1 to 1.5 hours you can have the head and cylinder off and can do the job properly . This would only cost you about $100. If there are peices in there and you run it , it could cost you upwards of $1000 ! Piston, new cylinder and still all the gaskets.



The whole job can be done in 4 hours at home. And you can update that base gasket if need be.



But there are reverse spiral easy-outs that will get that plug out. See your local Snap-on dealer for a higher quality one.

Good luck and let us know how it goes.
 

windaddiction

New member
imported post

imported post

Ya I know what your saying..... it doesnt take much to wreck an engine. We carbon locked a 750 KW DG at wrk.. not fun. I might just go ahead then buy the service manual and strip it down and build it up replace gaskets and rings maybe have the cylader honed... oh well!
 

windaddiction

New member
imported post

imported post

well got it all apart only other problem is one of the exhuast studs broke off too! but 'm taking it to get soem head work and hopefully put her back together this week! any of you thinking you can't do a job like thsi you are wrong I only had my 100$ craftsman tool kit and the manual in .PDF form.
 

Attachments

  • IMG_1557.jpg
    IMG_1557.jpg
    60.3 KB · Views: 0

joker650

Active member
imported post

imported post

Just be sure that when you have it together, before you crank it over, leave the spark plugs out , put it in gear and slowly turn the rear wheel. This will rotate the engine and you will know if the valve timing is correct. People have used the starter and ended up bending a valve.:ted::ted::ted:.

Be sure to use the copper base gasket. Don't use the old fiber styleone.



Have you thought about planing the head a little? I think I will try that next time mine is off.
 

windaddiction

New member
imported post

imported post

well it's back together and in the biek now just need to put on the carb and hook up some wires.... all went well i think... I did crank it over before i put in in by turning the cank and no prob so we should be good
 

windaddiction

New member
imported post

imported post

yes I pulled it... It's all back together now and it did run good actully but then it stalled and I can't start it now, I'm thinkngi weak battery and i may have flooded it! The only conern is that the clutch adjesment is way way way off so I gotta play with that some more and stuff!
 
S

Sixgill

Guest
imported post

imported post

When you get bored down your end you can come up this way and i can tour you around the hidden tofino/ukee sections.

Oh and if you time it right we can blast along the beach from the old wickanninsh to the long beach reserve at low tide. I know its not Oregon or the baja but its close to home.
 
E

ElChupacabra

Guest
imported post

imported post

windaddiction wrote:
Update got her going dead battery! runs even better than b4 I have insurance on it too ! les play!:dr:
I love a happy ending!:clap: Nice job windaddict!
 

windaddiction

New member
imported post

imported post

thanx lol.. thses air cooled singles are pretty simple to tear down..... mind you I didnt have to split the case so top end work is simple!
 

joker650

Active member
imported post

imported post

Yeah ....good job bro:tup:



But removing the motor was not needed. When I did mine I left it in the frame.
 
Top