Damaged Case

snackdaddy

New member
Long story short after a great day on the dunes my chain broke. The case saver almost did a great job but.... I got a hole in my case. It is a small pin hole with some significant scarring around to thepin hole.

My plan is to find someone willing to weld it on the bike....any ideas?

Plan 2 is split the case and have it welded. Downside will take me a LONG time to disassemble. Plus side Big Bore kit would be a mandatory upgrade.

Plan 3 split the case and install new one (about 500 us)

Any advice for anyone who has damaged their case?







Thanks



Mike
 

Cedartree

New member
imported post

imported post

That bites the big one Mike...:mad3:

Here's what I'd do...

Prop the bike up or lay itover so oil stops leaking out. This is crucial as the area must stay clean and dry prior to the repair attempt.

Clean the area as best you can, I like brake cleaner or carb cleaner in a spray can, or rubbing alcohol, or even hot water and soap if nothing else is available.Use a two part epoxy designed for metal repair such as JB Weld or Liquid Steel which should be available at auto parts or hardware stores, andfollow the instructions. Let it cure properly. My side case has such a repairfrom the PO that has lasted for many thousands of km's. No leaks so far. I don't recommend a weld repair on the bikeas it is too easy to introduce metal into the crank case. Also be aware that some (not all, but some) cases are magnesium alloy and shouldNOT be welded.

I've also heard of guys usinghi temp silicone gasket makeror rubbing a bar of soap on the hole, with good temporary results, but I recommendthe epoxy fix.That method would also allow you to fill in some of the scarring, too.

Good luck with the repair and have fun on the dunes.
 
S

supa666

Guest
imported post

imported post

maybe a really good cleaning around the area and then some jb weld would do the trick till you're ready to tear it apart..make sure theres no oil where your putting it and dont force any into the crankcase where it could do damage after hardening. Worth a shot to try and hold you through the beginning of the riding season. I've had some pretty wicked results with the stuff. even repaired a broken water jacket in an intake with it!
 

joker650

Active member
imported post

imported post

That happend to my old XT550.....chain broke and it actually broke off a big chunch of the case.



I layed it over and cleaned it up with brake clean as previously mentioned.

Then I used some coarse sand paper and scuffed all the paint off of the area about 1/4" from the hole.



Then I mixed up some "JB WELD".... smothered it all over a short3/4" bolt and put it in the hole.



I rode the bike for another 5 years or so and as far as I know it's still NOT LEAKING:tup:



good luck,

Note:

ur link didn't work for me so I didn't see what the damage looks like.

If there are many cracks then JB WELD may not work because the cracks will continue on after use.
 
G

Guest

Guest
imported post

imported post

What bike have you got, I have XR650l spares if that is what you are looking for. 2nd gear is gone and I'd like to keep the top end(piston, barrel valve cover) but the rest would be available for sale at a very reasonable price to help a bro out.

Good luck
 

Sparkle

New member
imported post

imported post

I think you guys are on the right track....I like JB weld too. If it's done right it will be stronger than the case. Make sure the hole is clean (carb cleaner is good, try to shoot some right through the hole). Push the JB Weld into the hole and it will lock from the other side.

I heard of using a self-threading screw smothered in JBW too.

Use JB Weld to body-putty the case scratches too. If the hole is deep, reinforce the patch with a piece of aluminum screen materialjust to hold the shape until it dries, then file or sand smooth and spray bomb with aluminum paint (optional).

Then forget it...

Sparkle
 

2Trider

New member
imported post

imported post

As everyone says...JB weld it and as said make sure it is free of all oils.

(I like the screen idea for re-enforcement if needed)

Canadian Tire usually has it as well



Next up a high quality linkless (fully riveted)chain with fresh sprockets with a solid chain guide block :tup:



Then go play hard again:clap:
 

snackdaddy

New member
imported post

imported post

Thanks for all the advice.

The JB weld solution scares me for two reasons.

I have never had JB weld hold in any other jobs I have used it on

I ride my bike hard and am scared of a failure deep in the bush

Any better products then JB weld?

I shall never ever by a CZ chain ever again. THe chain itself snapped not the masterlink.

I was very lucky the chain broke when it did. 5 minutes previous I was doing High speed runs on the beach.
 

Island Hopper

New member
imported post

imported post

I've done many repairs with JB weld and have had great success.... If you do the prepwork like Tom suggests and give it proper drying time chances are it will hold for a long time.... Your pics don't come up when I hit the link so I can't see the extent of the damage.....

I tried a CZ chain a couple years back with poor results..... Others have had good luck with them but in my case that chain was a poor investment....
 

cactusreid

Active member
imported post

imported post

snack daddy,i really like the newer versions of jb style epoxys. tech steel is one that i have used,that seems very good. it's a roll of putty that you cut a slice off,knead it together,and then press into place and let it dry well. as others have said.the prep is the important part for a good repair. you can even sand it to shape when it is set up. i got my last tube at the local auto parts store.
 
O

old trials guy

Guest
imported post

imported post

snackdaddy wrote:
Any better products then JB weld?

I have used this stuff with great success. Itis used for mounting through hull fittings on boats and we used it all the time for crankcase repairs in the Honda business. One of the few epoxies that can be drilled and tapped. In some cases we backfilled the hole and then glued a patch over the top for the next time the chain came off. Anything that gets that hot while curing must be good. :tup:

<<http://www.marinetex.com/marinetexepoxyputty.html>>

BTW, high speed passes on sand with a chain that has sticky lube on it and maybe on the tight side can be a disaster. Sand builds up on the chain effectively makes it tighter and then when you bottom the suspension under throttle something has to give. Better the chain than the countershaft!

otg
 
Top