Dorky's NEW new bike thread

2

2wheelHorseRider

Guest
imported post

imported post

Dr650 dreadnought wrote:
Hooligans your all hooligans, what ever happen to the days of Drs XLs n Klrs? 30+hp should be enough for anyone.

Today, we all have a bigger buttock & belly - so that's why we need more power. :)

"more power, more power, more power"
 

Bora20

Administrator
imported post

imported post

Speak for yourself. I have lost 40 lbs over the winter, my bike goes like stink now:dude:
 

XmikeR

New member
imported post

imported post

Beauty looking ride Gord! Im dripping with envy........ while waiting for new parts for my old girl.
 

Dorky

Moderator
imported post

imported post

Thanks Mike. You can ride it if we meet up at Tunkwa again. :clap:So what was the final assessment on your XR -what was the main busted part?
 

joker650

Active member
imported post

imported post

Dorky wrote:
Thanks Mike. You can ride it if we meet up at Tunkwa again. :clap:So what was the final assessment on your XR -what was the main busted part?

Don't Hi-Jack the thread :wi:

Go searching for his "repair thread" :mad3:..........................;)
 

Bora20

Administrator
imported post

imported post

Don't worry, with Dorky's track record, this will become the "new repair thread".

I am not sure if I am the pot or the kettle...:wi:
 

joker650

Active member
imported post

imported post

Hey Dorky.

Did u find a way to turn off ur electrics with the key on and the engine not running?

I ask because killing ur battery could cause u some real grief.

Ur new bike has a slipper clutch, so bunp-starts are prolly imposable :hr:
 

Dorky

Moderator
imported post

imported post

I haven't wired the grips yet - probably this week. I think I'm gonna use the kickstand switch as suggested (it seems that I do have one).

As for the slipper clutch, a little experimentation today shows that I can in fact bump-start the bike with no problems. :clap: When push-starting the bike I can't tell the difference between the slipper and a normal clutch. I can sure tell the difference when riding though - just gear down and pop the clutch out - the slipper eases you into lower gear with no skid or hop.

I think the issue with this bike (and others)will be the two ECUs and the FI. You need to have some power left over to boot the computers and pressurize the fuel system. Obviously this will be much less power than is required to turn over the bike so even when power is very low I should be able to push/pull/bump start it. But if the battery is deaddead, there is no bumping it into life.
 

Dorky

Moderator
imported post

imported post

Well, the grips are in and the hotpoint is there for the vest.

I couldn't use the kickstand switch because it's a fancy sealed magnetic switch with three wires and I have no idea how it works (and I'm supposed to be an electronics guy?). There was no obvious 'switching' just a change of about 5Mohm. And 5 volts were supplied to the switch on two of the three wires. ??

Apparently these switchesare pretty tough but it scares me because if I do wreck it there is no way to bypass it on the trail. KTM has a doodad you can useas abypass.
 

joker650

Active member
imported post

imported post

Yes it's bypassable.

My SE has the same switch and they by-passed it, we can do the same to urs.



It's a "Hull Effect" switch.
 

Bora20

Administrator
imported post

imported post

Hall effect switch or sensor; uses change in magnetic field to operate. I didn't keep all my electronics books away for nothing


:hb:
 

Dorky

Moderator
imported post

imported post

Bora20 wrote:
Hall effect switch
Yup, so I would have expected a supply voltage, ground, and an output that would be at ground in one state and at near supply voltage in the other state. It didn't seem to work that way :wi:
 

Bora20

Administrator
imported post

imported post

Dorky wrote:
Bora20 wrote:
Hall effect switch
Yup, so I would have expected a supply voltage, ground, and an output that would be at ground in one state and at near supply voltage in the other state. It didn't seem to work that way :wi:


Hmmm, some fancy Austrian switch. Did you move the kickstand back and forth while you had the meter on the circuit?
 

joker650

Active member
imported post

imported post

All they did was twist 2 of the 3 wires together.

I can look into it tomorrow.
 

Rib Eye

New member
imported post

imported post

FYI: Took a look at my bike - the kickstand switch only has two wires, not three. hmm?
 

Dorky

Moderator
imported post

imported post

Bora20 wrote:
Hmmm, some fancy Austrian switch. Did you move the kickstand back and forth while you had the meter on the circuit?
Yup.
 

Dorky

Moderator
imported post

imported post

Rib Eye wrote:
FYI: Took a look at my bike - the kickstand switch only has two wires, not three. hmm?
Hmmmm? Doesn't it go up into a triangular 3-wire connector? If your's goes to the same connector I should be able to figure out how to fool the ECU. (I'll assume the ECUs are the same).
 

Rib Eye

New member
imported post

imported post

No, on mine a harness follows from the kick stand switch & snakes stright up the frame, then there is a black 2-pin connector located at the aft left underside of the airbox (has one blue wire and one red wire). The harness thenroutes forward to behind the headlight area - I think.
 
Top