DR 650 Valves...??

Payback

New member
Hey Folks, I need to do my valves . I've never done them before , any tricks, tips, something I should look out for. my bike is a 2001 DR650.
thanks
 

joker650

Active member
imported post

imported post

Set with engine cold

Remove the tank and use compressed air to blow all the dirt and crap away from the wires and cables above the access caps.


EDIT:

Use a set of go/no-go gauges. They work the best:ted:
 

Payback

New member
imported post

imported post

thanks for the tip!

this is a newb question, but valves get tighter as they go longer without adjustment? an adjustment will result in opening up the clearance, not tightening it?

what is the best tool to use to move the adjustment rod , will it be hand tight, after the stop nut is loosened?
thanks
kurt
 

Payback

New member
imported post

imported post

So yeah, I did my valve clearance on sunday afternoon. Double checked settings and the bike sounds way different. What should I listen for , how should it sound???? Not that tough of a job , although stressful for the first time!, It seems to run fine I drove for around for about an hour or so , no change in the sound of the bike...please give me some input !!
 

joker650

Active member
imported post

imported post

Is there a loud 'ticking' coming from the top end? If not then they are prolly not too loose.:tup:

Is the bike hard starting? No..then they are prolly not too tight.:tup:

Does the bike start fine, but either stall and not re-start or loose power when the engine gets hot? No...then they are not too tight.:tup:

Does the engine backfire out the muffler and not start? No...thenthe exhaust valvesare prolly not too tight.:tup:

Does the engine back-fire out the carb and not start? NO... then the intake are prolly not too tight:tup:



The hardest one is the first one. The first time I set mine I was way out of wack (too loose)for some reason and it "ticked" like an old VW:mad3:
 

Payback

New member
imported post

imported post

the intake valve cover... is it on the front of the bike and the exhaust is towards the rear???

To find TDC..with your ratchet move the crankshaft counter clockwise, until I see the line with the "T". the compression stroke is is when the crankshaft is hard to move???
 

joker650

Active member
imported post

imported post



Does this help?

piston downbdc moving up tdc down bdc up

Intake () Compression () Power ()Exhaust.

In the cycle, the piston is at the top twice,on compression and at the end of the exhaust stroke and the beginning of the intake stroke.

The timing mark will line up twice in the cycle(2 rotations of the crank), once at TDC on the compression stroke and once at valve overlap(end of exhaust and beginning of intake stroke). SO as long as the pointer ligns up while the crank is hard to turn(piston under compression) u will be fine.

Remove the spark plug and hold your thumb over the hole. Gently rotate the crank by hand and get a feel for the compression and watch the mark. It's prety easy this way.

Good luck.





[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"][size=+1][size=+2]Intake Stroke[/size] [/size][/Font][/font]





[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]The intake stroke is the first of the four strokes in a four-stroke motor's combustion cycle. As the piston moves away from the top of the cylinder, the intake valve opens. The downward movement of the piston creates a vacuum (negative pressure) in the cylinder. The greater pressure outside the cylinder (ambient or atmospheric pressure) pushes the air/fuel mixture into the cylinder. Just as the piston reaches the bottom of the cylinder, the intake valve closes.[/Font][/font]












[align=center]
Intake%20Stroke.gif

[/align]






[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"][size=+2]Compression Stroke[/size][/Font][/font]





[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]The compression stroke comes next and begins as the piston starts to move upward in the cylinder. The intake valve closes, trapping the air/fuel mixture in the cylinder. Upward movement of the piston compresses the mixture into a very small area. This compression or squeezing of the mixture is very important for developing maximum power from the engine. The higher the compression, the greater the pressure exerted on the piston when the mixture is burned. Compression also "preheats" the mixture, which helps it burn more efficiently.[/Font][/font]










[align=center]
Compression%20Stroke.gif

[/align]





[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"][size=+1][size=+2]Power Stroke[/size][size=+2] [/size]
[/size]
[/Font][/font]



[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]The third stroke in the four-stoke cycle is the power stroke, which begins as the compressed air/fuel mixture is ignited in the combustion chamber. A spark plug, located in the cylinder head, creates an electrical spark that ignites the mixture, causing it to burn explosively. The burning mixture expands very rapidly, creating very high pressure against the top of the piston. This pressure drives the piston downward, which turns the crankshaft, which drives the motor. The up and down motion of the pistons in all four-stroke motors is converted to rotary motion by the crankshaft.[/Font][/font]










[align=center]
Power%20Stroke.gif

[/align]



[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"][size=+1] [/size][/Font][/font]

[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"][size=+1][size=+2]Exhaust Stroke[/size]
[/size]
[/Font][/font]



[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]The final stoke of the four-stroke cycle is the exhaust stroke. As the piston approaches the end of the power stroke, the exhaust valve opens. Pressure in the cylinder causes the exhaust gases to rush past the valve and into the exhaust system. The piston moves upward, pushing most of the remaining exhaust gases from the cylinder. As the piston nears the top of this stroke, the exhaust valve begins to close as the intake valve begins to open.[/Font][/font]










[align=center]
Exhust%20Stroke.gif

[/align]


[font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]The exhaust stroke completes the combustion process. The reopening of the intake valve signals the beginning of a new cycle, which occurs in each cylinder in the engine. The combustion cycle is repeated over and over at a very high rate of speed as long as the engine is running.[/Font][/font][font="Arial,Helvetica,Geneva,Swiss,SunSans-Regular,Verdana,Trebuchet MS,New Font"]
[/Font][/font]










[align=center]
[/align]
 

Payback

New member
imported post

imported post

joker......thanks VERY much, next time I'm through Kamloops, you'll get a beer or two!!
you always help my newb questions!

:hb:
 

joker650

Active member
imported post

imported post

Payback wrote:
joker......thanks VERY much, next time I'm through Kamloops, you'll get a beer or two!!
you always help my newb questions!

:hb:
I just hope I was right:hr:
 

Payback

New member
imported post

imported post

yep seems to be okay...I just got back from a 200km ride , she;s running great!

thanks again
 

Attachments

  • ds 007.jpg
    ds 007.jpg
    199.3 KB · Views: 0
Top