TW_rider
Member
We've all heard about this...like most, I was in denial about how my (relatively) new DR could have such a glaring and ignored fault.
Three seasons ago, I opened her up to have a look-see. What I found was not the Phillips head screws that everyone was complaining about...mine had FLANGED, Allen head cap-screws! A quick tug on the lower screw proved that it was firmly set and not coming loose.
Fast forward to this year...the nagging little voice was always in the background, so I decided that I would open her up and put my fears to rest once and for all.
Weekend all to myself...I set upon this task.
Within an hour or so, I had the DR lying in the grass so that I could work on her easier (but in hindsight, it would have been better to have her on the stand), and pulled the clutch cover off.
With the cover off, you can access the lower screw easily...the upper one...not so much. I've read how pulling the clutch basket makes the task easier, but it seemed a daunting task. Upon closer observation, it was obvious that I would not be able to complete this job PROPERLY, without pulling the basket.
Had to ride back to town to buy a 27mm socket.
Kicked her into gear...held the rear wheel with my foot and spun the clutch nut off with my impact driver...basket lifted out easily and now I could see BOTH NSU screws...this is better!
I removed the bottom one first, drilled it and re-installed it using the blue Surface Insensitive Loc-Tite. Then I moved to the upper screw
It was barely finger tight....there was absolutely NO EFFORT required to remove it...in other words...It was LOOSE!
Mine is a 2010, with barely 16000 kms (12,000 miles) and the top screw had already walked itself out of its place. If this screw can get that loose in 16,000 km...I shudder to think what might have happened if I had let it go any longer!
I repeated the drilling and installation with the Blue Loc-Tite and then safety wired the pair together, so that they will never come out!
Yeah...I know...it's not the best tie-wiring job, but it will do the trick.
SO...if you own a DR650 with over 16000 km, I urge you to think about doing this fix. It's fairly easy...you'll need new oil and filter and possibly a new gasket, and about 3 hours of your day.
There are plenty of instructional tutorials online...pick whichever works best for you.
I would recommend removing the clutch basket...it adds about 15 minutes to the job, but it gives unfettered access to both screws - this isn't a job you want to cut corners on.
Just remember that when using Loc-Tite...it requires 24 hours to cure. That means, you shouldn't do this job, then refill with oil and go riding the same day!
Do it once, do it right.
Good luck.
Three seasons ago, I opened her up to have a look-see. What I found was not the Phillips head screws that everyone was complaining about...mine had FLANGED, Allen head cap-screws! A quick tug on the lower screw proved that it was firmly set and not coming loose.
Fast forward to this year...the nagging little voice was always in the background, so I decided that I would open her up and put my fears to rest once and for all.
Weekend all to myself...I set upon this task.
Within an hour or so, I had the DR lying in the grass so that I could work on her easier (but in hindsight, it would have been better to have her on the stand), and pulled the clutch cover off.
With the cover off, you can access the lower screw easily...the upper one...not so much. I've read how pulling the clutch basket makes the task easier, but it seemed a daunting task. Upon closer observation, it was obvious that I would not be able to complete this job PROPERLY, without pulling the basket.
Had to ride back to town to buy a 27mm socket.
Kicked her into gear...held the rear wheel with my foot and spun the clutch nut off with my impact driver...basket lifted out easily and now I could see BOTH NSU screws...this is better!
I removed the bottom one first, drilled it and re-installed it using the blue Surface Insensitive Loc-Tite. Then I moved to the upper screw
It was barely finger tight....there was absolutely NO EFFORT required to remove it...in other words...It was LOOSE!
Mine is a 2010, with barely 16000 kms (12,000 miles) and the top screw had already walked itself out of its place. If this screw can get that loose in 16,000 km...I shudder to think what might have happened if I had let it go any longer!
I repeated the drilling and installation with the Blue Loc-Tite and then safety wired the pair together, so that they will never come out!
Yeah...I know...it's not the best tie-wiring job, but it will do the trick.
SO...if you own a DR650 with over 16000 km, I urge you to think about doing this fix. It's fairly easy...you'll need new oil and filter and possibly a new gasket, and about 3 hours of your day.
There are plenty of instructional tutorials online...pick whichever works best for you.
I would recommend removing the clutch basket...it adds about 15 minutes to the job, but it gives unfettered access to both screws - this isn't a job you want to cut corners on.
Just remember that when using Loc-Tite...it requires 24 hours to cure. That means, you shouldn't do this job, then refill with oil and go riding the same day!
Do it once, do it right.
Good luck.
Last edited: