Legal Alien
New member
Okay, I've been trying to make my 2002 F650 Dakar quicker in the low and mid range. The good news is I've succeeded beyond my expectations and now, any of you who own one can do this whole job with a lot af patience and around $500. Here's how:
It all revolves around making the bike breath better. The snorkel air duct is pathetic and doesn't get enough air to the engine. Cut a hole in it approx 3/4" deep and about 2" long on the inside, right at the front end. This opens it up properly and when coupled with a BMC air filter (which is a pig to instal and involves dismantling the whole air box), the bike gets enough air in.
The next job involves getting rid of the idiotic exhaust system which completely contradicts any laws of gas flow ever. As you know, there are two 90 degree junctions for the exhaust gases to negotiate while they're buffeting around their twin canisters, "Useless!" It's a complete swine to remove and you better put all of your tools next to the bike before you start, including a hammer (honestly), watch screwdrivers, torx drivers, socket set, spanners and a Red Bull to give you the necessary "wings" required to pull it off its header pipe. You also have to loosen the left side of your rack (if you have one fitted) and remove the license plate assembly, (or at least remove the left side torx screw and let it pivot out of the way on the right-hand screw).
Obviously, you don't just leave it without an exhaust attached and the choice of replacements seems endless. However, just try to buy these things in N. America - it's not easy. I ended up plumping for a Two Brothers Racing "slip-on." "Slip-on, my arse!" Nothing fits particularly well and the fastners provided look really nice but don't work. Save yourself the trouble and go to Lordco where you can buy a 1 3/4" clip that looks the same as the oversized one that TBR supply - you'll also need a junior hacksaw to cut the excess thread down afterwards and a file to remove the sharp bits if you're as anal as me (once the whole job is complete). Oh...., and buy some exhaust gasket sealant becuase TBR supplied me with a tube of concrete. Put the sealant on the inside of the TBR supplied s-shaped tube at the end with the cuts in it and also on the inside of the exhaust can that connects to the s-shaped tube. All of the tubes slip much further on than you'd expect, so don't be alarmed when your s-shaped tube slips about 3" over the header. Also, leave the whole plot for a couple of days to dry or your newly created soft gasket will fire itself all over the place when you start the bike. The tubes of sealant lie and it does not dry within 24 hours!
I'm not a fan of loud exhausts and the TBR unit is certainly that but, the fuel injection system compensates for all of the changes without adjustment and though the bike now makes Huskys sound like toys, it goes phenomenally well and will not be getting itself replaced with anything else for quite a while.
If you have any questions, PM me or reply to this thread. The job was a proper nightmare and if I can save others time, consider this my inaugural favour to you, my fellow folks at DSBC.
It all revolves around making the bike breath better. The snorkel air duct is pathetic and doesn't get enough air to the engine. Cut a hole in it approx 3/4" deep and about 2" long on the inside, right at the front end. This opens it up properly and when coupled with a BMC air filter (which is a pig to instal and involves dismantling the whole air box), the bike gets enough air in.
The next job involves getting rid of the idiotic exhaust system which completely contradicts any laws of gas flow ever. As you know, there are two 90 degree junctions for the exhaust gases to negotiate while they're buffeting around their twin canisters, "Useless!" It's a complete swine to remove and you better put all of your tools next to the bike before you start, including a hammer (honestly), watch screwdrivers, torx drivers, socket set, spanners and a Red Bull to give you the necessary "wings" required to pull it off its header pipe. You also have to loosen the left side of your rack (if you have one fitted) and remove the license plate assembly, (or at least remove the left side torx screw and let it pivot out of the way on the right-hand screw).
Obviously, you don't just leave it without an exhaust attached and the choice of replacements seems endless. However, just try to buy these things in N. America - it's not easy. I ended up plumping for a Two Brothers Racing "slip-on." "Slip-on, my arse!" Nothing fits particularly well and the fastners provided look really nice but don't work. Save yourself the trouble and go to Lordco where you can buy a 1 3/4" clip that looks the same as the oversized one that TBR supply - you'll also need a junior hacksaw to cut the excess thread down afterwards and a file to remove the sharp bits if you're as anal as me (once the whole job is complete). Oh...., and buy some exhaust gasket sealant becuase TBR supplied me with a tube of concrete. Put the sealant on the inside of the TBR supplied s-shaped tube at the end with the cuts in it and also on the inside of the exhaust can that connects to the s-shaped tube. All of the tubes slip much further on than you'd expect, so don't be alarmed when your s-shaped tube slips about 3" over the header. Also, leave the whole plot for a couple of days to dry or your newly created soft gasket will fire itself all over the place when you start the bike. The tubes of sealant lie and it does not dry within 24 hours!
I'm not a fan of loud exhausts and the TBR unit is certainly that but, the fuel injection system compensates for all of the changes without adjustment and though the bike now makes Huskys sound like toys, it goes phenomenally well and will not be getting itself replaced with anything else for quite a while.
If you have any questions, PM me or reply to this thread. The job was a proper nightmare and if I can save others time, consider this my inaugural favour to you, my fellow folks at DSBC.