Lowering DRZ400 ???

c337b

Moderator
Looking at buy a DRZ400 dualsport. Has anyone lowered one?? How much?? What did you do to lower it? How did it effect the performance? I am 5' 7" with 30" inseam. I am tippy toed sitting on it I would like to lower it 2-3" Only link I have found is below. If it can't be done then I will go for a DRZ650 and have the forks reworked. I find they are to soft for trail riding. Never riden a 400 how do they compare?



Thanks

Frank

http://www.koubalink.com/
 

SubMann

New member
imported post

imported post

I lowered mine. I have similar dimensions. In other words I'm a short ass too.

I got the 0.75" Koubalink. I've never bottomed out. I understand the longer links make the back real soft and you can bottom out the shock a lot. I also got bar risers and raised the forks in the triple clamps. I topped it off with a gel seat an I'm lovin it.

I couldn't even get the ball of my foot on the ground before. Now it is much better.
 

c337b

Moderator
imported post

imported post

Subman



Iwill be in Victoria tommorrow any chance of taking a look at your bike to see how it fits me



Frank
 

Floored

Active member
imported post

imported post

c337b,

Depending on what kind of riding you are shooting for, you can also carve out some foam from your seat. Anyone who's seen what I did to mine can vouch for how much lower you can get (3 inches). However, if you want cush, that ain't the way.
 

04klr

Well-known member
imported post

imported post

touching the ground is highly overrated, the bike should fit when you're riding it, keep your feet on the pegs (practice trackstands and Hans Rey moves) ;}
 

JavaJude

Super Moderator
imported post

imported post

I ride a DRZ 400 and I HAD to put Kouba Links 3s in. Inow can reach the ground on my tip toes (I'm barely 5'7"). I ride this bike mainly off-road and once in a while through some pretty gnarly stuff (check out the photos in the photo gallery and you'll see what I mean) and lowering it has caused some suspension issues but as long as I don't hit those crossditches too hard I'm ok. I had to lower the front forks after installing the Kouba Links so it didn't feel like I was riding a chopper. Then I tighten the center spring so it didn't have as much travel. The bike isn't as soft as it was when I started but again, I can touch the ground. All in all I think I was able to lower the bike by 1 3/4".

Now that I am use to riding the bike I think I will raise it up a bit (Kouba Link 1). The problems that I am having are mainly when I get into really toughstuff and the bike starts to tip over and my feetcan't feel the ground until it's too late. But these are usually low speed tip overs and it's only my pride that gets hurt.

There was afellow that I know that was told not to use the Kouba Links and that if he wanted to lower the bike he should get a"professional" todo it for him. I think he was quoted about $600-$800 to get it done. That's another route that you can take. I'm not a hard-core rider and I don't think that I'm doingdamage to mybike. I am aware thatmy bike does bottom out if I take things too hard so Idon't.

-Judy-
 

scottbc

Member
imported post

imported post

JavaJude wrote:
There was afellow that I know that was told not to use the Kouba Links and that if he wanted to lower the bike he should get a"professional" todo it for him. I think he was quoted about $600-$800 to get it done. That's another route that you can take. I'm not a hard-core rider and I don't think that I'm doingdamage to mybike. I am aware thatmy bike does bottom out if I take things too hard so Idon't.

-Judy-

Hi Judy,

I think that I'm that guy. I was quoted about $600.00 by RMR Suspensions to do the job correctly(professionally). This included new springs front and rear, also shortening of both front springs and rear shock. From what I can gather the problem is that the Kouba Links alter the amount of mechanical advantage on the spring,meaning that for a given riders weight a heavier spring will be required to work correctly.

Now I am lucky, and cheep. I checked the stock spring rates on an on line calculatorand have found that at my light weight ( 140lbs wet) that the front springs are the right rate. The rear spring is slightly on the heavy side. I am hoping that I can add Kouba Link 1 or 2 and be able to set up the race and static sag to within spec. I will add a 1" bar riser and move up the forks on the front to compensate for the lowered rear.

For a great explanation of static and race sag set up go to thumpertalk.com, there is a really good description of the proceedure with pictures and all.

Bottom line, use the links but set up the suspension to spec and it should work. If you are super agressive and expect to ride like a MX'r spend the big bucks and have it done professionally.

Thats my plan, I hope that it works as planned. Lots of info and advice available online, it just takes some time and patience to find it and filter out the fluff.
 

Floored

Active member
imported post

imported post

So have you figured out if you're going to be using it to get to the dirt, or truely using it for all around riding? Personally I'd say "cut the stock seat" and keep your ground clearance on the dirt. If you also want an "all-arounder", order a replacement saddle (Corbin, etc...) for that riding, as the stock one hurts anyways.

Compare my Avatar to stock, I think you'll find all the lowering you'll need.
 

JavaJude

Super Moderator
imported post

imported post

Hi scottbc. Yes, you are the guy that I was talking about in my previous post on this topic. I'm glad that you've come up with a solution for lowering your DRZ.

I hope you'll be joining us on the Newbie Ride on October 21.
 
Top