Need help in drilling out a broken Bolt.

North

Active member
The Kick Stand broke off on my ktm. I need to get out half of the bolt that was left in the bike. Today I have bought 3 different drill bits, but none of them will drill a hole in broken bolt.

I have a screw remover, but I need a drill bit that will cut into the bolt, so I can but the screw remover in.

Any ideas on what bit to get and were to get it from. The last bit I got was a ridgid "cold fire" metal Cobalt drill bit. But it did nothing but smoke. aaggg. :mad3:
 
F

franhoser

Guest
imported post

imported post

Rick,

Not sure on the drill you're using. Some of the battery type drills are lower RPM's and you could be there all day creating smoke. You need an electric type with higher RPM's and good metal bit should really do the trick. Sometimes try the smaller drill bits to cut in and then work your way up to what ever size hole you need.
 

North

Active member
imported post

imported post

Thanks,

I am using a Dewalt plug in drill. It's rated at 5.4 amps, 2,500 rpm.

I tryed smaller drill bits too.

Do I need cutting oil?

aagg:mad3:
 

farmerger

Member
imported post

imported post

Two suggestions. 1. try a small drill bit in a Dremel, then work your way up. 2. If a part of the bolt is still sticking out, get a cutting disc for the Dremel and cut a groove in the bolt. Then try to get it out with a flat head screw driver.
 
O

old trials guy

Guest
imported post

imported post

I have had good success through the years using a very sharp, small cold chisel. I chisel a slot in bolt angled in the direction I want it to turn. Then I impact it out turning the bolt with the chisel and a hammer. It sounds crude but works on stubborn bolts. My guess is the bolt is a high grade steel or possibly hardened as it acts as a pivot and holds quite a load.Wear safety glasses so you don't loose an eye ;)

Heating with a torch can also help.

Good luck....otg
 
F

franhoser

Guest
imported post

imported post

see this is what happens when I asked you sell me that bike and you didn't.



:D:D:D:D:D:D:D:D:D:D
 

North

Active member
imported post

imported post

I think I am cursed.:shock:

I will try to get a drill bit for my Dremel, nothing is working.

No part of the bolt is sticking out. So a Have to drill a hole in it.
 

skidmark43

Administrator / BFF in the blue jacket
imported post

imported post

North wrote:
I think I am cursed.:shock:

I will try to get a drill bit for my Dremel, nothing is working.

No part of the bolt is sticking out. So a Have to drill a hole in it.

The advice above should have you on the track to success. I wanted to confirm that you've been able to use a centre punch and will be using cuttin oil...

Patience & good luck,

Mark
 

c337b

Moderator
imported post

imported post

Snap-on sells a Hi-Roc carbide drill. Will drill thru any bolt, not cheep though, a 3/16" bit costs 37.00 Used one to drill out a broken easy out. Cut thru it like cheese

Frank
 

Mad Max

New member
imported post

imported post

I have welded out hundreds of bolts from Cats to cameras. The smaller the harder.Use arctec unicrom or stainless and dab'dab'dab until it is protruding out enough to weld on a nut or grab with vise-grips.Just be sure to only hit the bolt and not weld the bolt to the base metal.Good luck

Jay
 

North

Active member
imported post

imported post

Thanks Guys,

I just got some cutting oil. I couldn't find a drill bit for my Dremil though. Do Dremils spin in both directions?? I couldn't find a direction switch on mine.

If I could get my hands on one of those 37 dollar snap-on bits, I would buy one.

My drill says it spins at 2,500 rpm. Is that fast enough?
 

eagleguy

New member
imported post

imported post

is your drill variable speed? I think slow is better IMHO

where are you in surrey, I may come over . call me 604 888 6691. steve
I see your'e at work, so try heating the part around the bolt and spray with WD or the like. Then go with otg idea of small chisel.
 
F

Fumanchu

Guest
imported post

imported post

Blast out the middle of the bolt with a cutting torch and then quench the remainder of the bolt with water to shrink it just before you easy out whats left.A good muffler shop can do this for you.
 

Buck

Moderator
imported post

imported post

Mad Max wrote:
I have welded out hundreds of bolts from Cats to cameras. The smaller the harder.Use arctec unicrom or stainless and dab'dab'dab until it is protruding out enough to weld on a nut or grab with vise-grips.Just be sure to only hit the bolt and not weld the bolt to the base metal.Good luck

Jay
Great tip, we also do this in the shop. Sure beats drilling! North probably doesn't have an arc welder though.
 

Sparkle

New member
imported post

imported post

The pivot bolts on kickstands are usually a hardened high quality bolt grade 8 or better so drilling with a normal HSS bit will be almostimpossible.Usually it is also an interferance fit to make sure it doesn't unthread so it will be stiff to turn.

The drill bit that might work would be a tungsten carbide drill bit usually available at machine shop supply stores. Getting a hole started will be a problem and centerpunching won't work.

Some suggestions might be to use a dremmel with a small "green" grindstone (hard to make a deep enough hole), or buy a couple of small carbide drill bits. If you manage to get a hole big enough for an extractor or "easy-out", you may have to heat the frame lug to get it to turn and tap the frame-lug as you turn with a hammer.

Another common trick is to hold a suitable sized nut over the broken shaft with vise-grips and weld the interior of the nut with a stickwelder. Even if the broken end is low in the hole, the weld will stick to the shaft only (if you don't overheat it). Twist it out before it is cool. I watched a HD mechanic do this on a delicate part and he never even scorched the paint...

......well, maybe a little....

Sparkle
 

joker650

Active member
imported post

imported post

Lets see a pic of this mess.

Is the bolt in steel or aluminum?



If ur going to drill...go buy a cpl reverse twist bits.

That way when drilling, if the bit grabs, usually the bolt will thread right out of there.



But sometimes these things are best taken to a reputable welder.

As mentioned before.... Anothe really good way to remove it is to get a nut welded to it.

The heat that goes through the bilt from the weld helps expand the bolt and the threaded hole. When the peice cools (but nnot too much) the bolt usually threads right out.
 

North

Active member
imported post

imported post

I am at still at work and I am going riding on the Husky in morning. So I will post a picture tomorrow evening.

thanks
 

Buckethead

New member
imported post

imported post

Hey Rick -
I have a torch, an arc welder, and beer if you need. Just come on by.
Matthew
 

04klr

Well-known member
imported post

imported post

I presume the back (remaining) side of the bolt isn't accessable, to grab andthread in either direction to grab/slot/chisel/weld,
 

North

Active member
imported post

imported post

No it's not.


I am going to take-up buckethead's offer. I can't get the bloody thing out.
 
Top