Warped rotor or what?

PistolPete

New member
2000 DR650...about 3000km on new EBC rotor and pads

Okay...so here's the scenario. When I apply the front brake it feels like I get normal braking pressure for about 4/5th's of a revolution, then there is a noticeable let off in braking power for a short instant. It is, of course, more noticeable when I am going slower. Braking at 60kph it is hardly noticeable...I assume because of the higher rpm of the rotor. If I jack the bike up and hold the brake lightly and move the wheel, there is definately a spot where there seems to be less braking pressure. I have inspected the rotor for damage...nothing. It doesn't appear to be warped, but I don't have the tools to do a "run out" test. If the rotor was warped shouldn't the pads "float" to follow the warp? I have already taken the rotor off, rotated it by one bolt hole, and reinstalled it.....same thing happens.

It almost seems like there is oil or something on a tiny spot on the rotor....but I have cleaned it with brake cleaner already.

Any idears?
 

Cedartree

New member
imported post

imported post

:ted:
HMM... in the automotive worldwe would describe that as "thickness variation". sounds like the rotor is true but probably not the same thicknessat all points between the pad contact surfaces. this results in the caliperpiston travelling in and out slightly to follow the rotor and a noticeable feedback through the lever, or perceived lessening of braking force,as thethicknessof the rotor increases then decreases. we use a micrometer and usually measure the rotor thickness in 6 or 8 places around the circumference. there might be a spec in the factory service manual.

a small amount of rotor runout is normal and not usually noticeable due to the fact that most calipers are floating and not solidly bolted to the bike, but float on two or more guide pins that allow side to side movement to compensate for pad wear.

the leading causes are a rotor that was not true to begin with, or a dirty or out of true rotormounting surface which then caused said rotor to rub against the padsmore in one spot than anywhere else, could also be aslightly seizing caliper piston or guide pin but that wouldusually generate heat, dust and possibly noise.

this stuff is what i've learned from trade school and then at aFord dealership as a tech. a disc brakeis a disc brake...:ted:
 

PistolPete

New member
imported post

imported post

Thanks Cedar.

That's pretty much what I have read while researching it on the internet. Google at it's finest. What the heck would we do without google?

It sounds like when I put the new rotor on I didn't clean the mating surface well enough. I noticed when I spun the rotor by one bolt hole that there was some crud between the rotor and hub. I cleaned it as best I can and I will see if it made any difference tomorrow. It may be too late. From what I read the misalignment causes the pad to rub the rotor in one spot over and over again...thus reducing it's thickness at that point.

Anyone know if MC rotors can be machined....or am I destined for a new rotor after only 3000km's?
 

Cedartree

New member
imported post

imported post

sorry to be the bearer of bad tidings, BUT it is most definitely too late for that rotor

machining rotors has pretty much fallen by the wayside in our industry, mostly due to the (relatively) low replacemment cost compared to the labor cost to resurface the rotor which is then that much thinner and more likely to warp. most likely by the time you find a machinist with the correct mounting fixtures to resurface the rotor and pay him to do it, the cost of a new rotor will be pretty attractive. skilled labor ain't cheap.

the other issue being thatthe machinist would probably have to take so much metal off the rotor to get the surfaces true again that the rotor would be at or below the manufacturers minimum thicknes spec.

buy the new rotor, be very careful to have the mounting surfaces spotless, and you should enjoy years of trouble free service.
 
Top