Casual Breaky/Coffee @ Bruces. June,July,August.

Phoenix

Phoenix

New member
240th & Lougheed Hwy., Maple Ridge. Generally Sundays @ 9:00 a.m. All are welcome to attend. Sometimes riding sometimes not, previous breaky threads will give an idea of what it's about.

I will be goin' for breaky this Sunday June 6th @ 9 a.m. Not sure if I'll be riding after breaky though.

Cheers, Alex.
 
Last edited:
DRuZer

DRuZer

Member
I'll see you there. Fig'r I'll drag out the bimmer just in case theres' a a ride to be done.....

Guy
 
T

tobster

New member
Thanks to Phoenixs help yesterday the DR is now back on the road and itching to go..............see ya in the morning
 
X

XT350

New member
Hi I'm sure there is room for another duelsporter at Bruce's. See you guys tommorow Rob (suzuki dr650)​
 
Farp

Farp

Active member
I'm looking for somebody to come with me up to the Kookipi rock slide tomorrow. I gotta see for myself if it's do-able or not. I'll be at Bruces tomorrow morning, 9:00am have breaky then truck the bikes up to Harrison Hot Springs and ride from there.

John
 
M

motorambler

New member
Anyone with a birds eye weather forecast for the Maple Ridge / Mission area? Either way, I'm headin to Bruce's :)
 
Last edited:
DRuZer

DRuZer

Member
fair weather riider

fair weather riider

Looks like I'm sitting staying home due to weather.
Should be changing fork oil anyways....

have fun
 
Phoenix

Phoenix

New member
Good breaky, Old Phart went to sling some mud(on the flats) and interested to hear the other riders report on E. Harrison/Kookipi Pass conditions.

Alex.
 
Old Phart

Old Phart

New member
Phoenix said:
Good breaky, Old Phart went to sling some mud(on the flats) and interested to hear the other riders report on E. Harrison/Kookipi Pass conditions.

Alex.
Click to expand...
The mud flats are a lot of fun and a relatively safe place for a newbie to practice popping wheelies, power sliding and all that other fun stuff.
 
xr8d

xr8d

New member
I'm in, no plan on where to go though, but need to get out!! (too much work!) Are you going at 9?

Jon
 
M

motorambler

New member
I normally show up round 9:30-ish cuz I don't do the greasy breakfasst :) I'm about to go into the garage & put the bike together & take it for a spin. If all goes well I'll be going to Bruce's. Will report back in a bit :)
 
M

motorambler

New member
Bike is all back together but noticed the starter switch has failed. The yellow "start" button has sunk inside the housing. I took the housing apart & noticed the start button pushes against a spring which sits between the button & a circuit board. Well, that circuit board is cracked. I can't believe I got 2 very rare Sundays off & will have zero riding to show for it :mad:
 
S

scottbc

Member
Don't miss you days ride. Wire up a temp. switch or even just cut the wires off the board, pull them out of the housing so that you can reach them, strip the ends 1/8 and instant hot wire.


motorambler said:
Bike is all back together but noticed the starter switch has failed. The yellow "start" button has sunk inside the housing. I took the housing apart & noticed the start button pushes against a spring which sits between the button & a circuit board. Well, that circuit board is cracked. I can't believe I got 2 very rare Sundays off & will have zero riding to show for it :mad:
Click to expand...
 
M

motorambler

New member
scottbc said:
Don't miss you days ride. Wire up a temp. switch or even just cut the wires off the board, pull them out of the housing so that you can reach them, strip the ends 1/8 and instant hot wire.
Click to expand...
Scott, I owe you a beer :) I did exactly as you said & got the bike going real easy! I raced out to Bruce's in the morning but didn't get there til just before 10:15. Some guys on cruisers said some guys on dirtbikes had "just left", so I missed you guys by minutes :( The day wasn't a total waste, since I spent some time enjoying McNutt :) Thanks again, Scott!
 
You must log in or register to reply here.
Top