Gnarly Parts 2nd Annual Dual Sport Event

F

franhoser

Guest
Dave/lori,

Please take my name off the list. I can't make it. Hope you have a great event and I'll come visit you guy's when I'm in the Chilliwack area.

Lev
 

TW_rider

Member
I am a little unsure if I should be riding the B or A route?
How tame is the B route?

From what I saw of the map, you would have to be a competent rider for the B loop. It goes up some portions of Vedder, Tamihi and Cheam/Archibald that some might consider as "intermediate"...
 
Last edited:

TW_rider

Member
TW-200 2Up? :spl:

Yeah, it's quite a sight! :D


Update: DAMN....DAMN...DAMN! A toasted source-coil means that I'm going to have to withdraw from this one! DAMN...I was so looking forward to it!
Now, I'm out of action for up to TWO WEEKS!!!

Shoulda bought the DR....
 
Last edited:

Lucky

New member
Yeah, it's quite a sight! :D


Update: DAMN....DAMN...DAMN! A toasted source-coil means that I'm going to have to withdraw from this one! DAMN...I was so looking forward to it!
Now, I'm out of action for up to TWO WEEKS!!!

Shoulda bought the DR....

whatsup with your coil?
 

TW_rider

Member
Tried starting her up this morning...nothing doing...no spark.
Did all the obvious checks, then went to the manual for a more in-depth type of troubleshooting. When I metered the pulse coil, it was OK but the source coil should be around 600 to 900 ohms...it was over 750,000. Of course, they mount the source coil along with the generator coils, so you have to buy a whole new stator assembly...$289 and two weeks waiting cuz it comes directly from Japan!
Not only that...but I sheared off one of the Allen bolts...and to make matters worse, it was one that didn't even need to come out!

I learned some new expletives today!

Wife said I should do the run on my Honda CT90...I declined.
 

dirtrider

Member
Now I might not make it, Couldnt even push my bike out of the shop. But once I got it out it was wheelies everywhere. But it made me aware that I am not in good enough health to do a loop and Ted wont baby sit me on the c loop soooooo. I might show up later and just do a short ride in some sections.....If I can find a baby sitter for me...
 

Lucky

New member
Tried starting her up this morning...nothing doing...no spark.
Did all the obvious checks, then went to the manual for a more in-depth type of troubleshooting. When I metered the pulse coil, it was OK but the source coil should be around 600 to 900 ohms...it was over 750,000. Of course, they mount the source coil along with the generator coils, so you have to buy a whole new stator assembly...$289 and two weeks waiting cuz it comes directly from Japan!
Not only that...but I sheared off one of the Allen bolts...and to make matters worse, it was one that didn't even need to come out!

I learned some new expletives today!

Wife said I should do the run on my Honda CT90...I declined.

:( oh...
 

Gnarly Dave

I'm a DSBC sponsor. Please thank me with your busi
I just got back from arrowing the A/B Loop from Chipmonk to bridle falls and all three of us ranned out of gas and light. Had to take whatever gas was left from the three bikes to put into one bike and road that bike over the goat trail for gas. Got gas and rode back up to fill up the other bikes. My bike light wouldn't work because my battery went flat. Had to go over that goat trail three times and the last time with zero light. Fun. Now I got to get up at 6 just to finish the arrowing for tomorrow.

Hope I get it all done and will see you all tomorrow.

Dave
 

Ti welder

New member
Yeah, it's quite a sight! :D


Update: DAMN....DAMN...DAMN! A toasted source-coil means that I'm going to have to withdraw from this one! DAMN...I was so looking forward to it!
Now, I'm out of action for up to TWO WEEKS!!!

Shoulda bought the DR....
Don't know about the source coil but I idid rewinde the generator side of my stator, cost about 50$ and a day. All you do is get the right size magnet wire and some epoxy. After the rewind I used Artic silver on the stator to case mating surface to help disapate some heat.
 

Lucky

New member
I just got back from arrowing the A/B Loop from Chipmonk to bridle falls and all three of us ranned out of gas and light. Had to take whatever gas was left from the three bikes to put into one bike and road that bike over the goat trail for gas. Got gas and rode back up to fill up the other bikes. My bike light wouldn't work because my battery went flat. Had to go over that goat trail three times and the last time with zero light. Fun. Now I got to get up at 6 just to finish the arrowing for tomorrow.

Hope I get it all done and will see you all tomorrow.
Dave


was 150km?
Is there gas near start point?
 

Lucky

New member
. Now I got to get up at 6 just to finish the arrowing for tomorrow.

Hope I get it all done and will see you all tomorrow.

Dave

Do you have gps tracks for the loops. You can send them out in the morning to the registered people. It can help.
 
Top